309 lines
8.2 KiB
C
309 lines
8.2 KiB
C
/*
|
|
* Copyright 2013 Michael Ossmann
|
|
* Copyright 2013 Benjamin Vernoux
|
|
*
|
|
* This file is part of AirSpy (based on HackRF project).
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2, or (at your option)
|
|
* any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; see the file COPYING. If not, write to
|
|
* the Free Software Foundation, Inc., 51 Franklin Street,
|
|
* Boston, MA 02110-1301, USA.
|
|
*/
|
|
|
|
/*
|
|
* This is a rudimentary driver for the W25Q80BV SPI Flash IC using the
|
|
* LPC43xx's SSP0 peripheral (not quad SPIFI). The only goal here is to allow
|
|
* programming the flash.
|
|
*/
|
|
|
|
#include <stdint.h>
|
|
#include "w25q80bv.h"
|
|
#include "airspy_core.h"
|
|
#include <libopencm3/lpc43xx/ssp.h>
|
|
#include <libopencm3/lpc43xx/scu.h>
|
|
#include <libopencm3/lpc43xx/gpio.h>
|
|
#include <libopencm3/lpc43xx/rgu.h>
|
|
|
|
uint8_t device_id;
|
|
|
|
/*
|
|
* Set up pins for GPIO and SPI control, configure SSP0 peripheral for SPI.
|
|
* SSP0_SSEL is controlled by GPIO in order to handle various transfer lengths.
|
|
*/
|
|
|
|
void w25q80bv_setup(void)
|
|
{
|
|
const uint8_t serial_clock_rate = 2;
|
|
const uint8_t clock_prescale_rate = 2;
|
|
|
|
/* Reset SPIFI peripheral before to Erase/Write SPIFI memory through SPI */
|
|
RESET_CTRL1 = RESET_CTRL1_SPIFI_RST;
|
|
|
|
/* Init SPIFI GPIO to Normal GPIO */
|
|
scu_pinmux(P3_3, (SCU_SSP_IO | SCU_CONF_FUNCTION2)); // P3_3 SPIFI_SCK => SSP0_SCK
|
|
scu_pinmux(P3_4, (SCU_GPIO_FAST | SCU_CONF_FUNCTION0)); // P3_4 SPIFI SPIFI_SIO3 IO3 => GPIO1[14]
|
|
scu_pinmux(P3_5, (SCU_GPIO_FAST | SCU_CONF_FUNCTION0)); // P3_5 SPIFI SPIFI_SIO2 IO2 => GPIO1[15]
|
|
scu_pinmux(P3_6, (SCU_GPIO_FAST | SCU_CONF_FUNCTION0)); // P3_6 SPIFI SPIFI_MISO IO1 => GPIO0[6]
|
|
scu_pinmux(P3_7, (SCU_GPIO_FAST | SCU_CONF_FUNCTION4)); // P3_7 SPIFI SPIFI_MOSI IO0 => GPIO5[10]
|
|
scu_pinmux(P3_8, (SCU_GPIO_FAST | SCU_CONF_FUNCTION4)); // P3_8 SPIFI SPIFI_CS => GPIO5[11]
|
|
|
|
/* configure SSP pins */
|
|
scu_pinmux(SCU_SSP0_MISO, (SCU_SSP_IO | SCU_CONF_FUNCTION5));
|
|
scu_pinmux(SCU_SSP0_MOSI, (SCU_SSP_IO | SCU_CONF_FUNCTION5));
|
|
scu_pinmux(SCU_SSP0_SCK, (SCU_SSP_IO | SCU_CONF_FUNCTION2));
|
|
|
|
/* configure GPIO pins */
|
|
scu_pinmux(SCU_FLASH_HOLD, SCU_GPIO_FAST);
|
|
scu_pinmux(SCU_FLASH_WP, SCU_GPIO_FAST);
|
|
scu_pinmux(SCU_SSP0_SSEL, (SCU_GPIO_FAST | SCU_CONF_FUNCTION4));
|
|
|
|
/* drive SSEL, HOLD, and WP pins high */
|
|
gpio_set(PORT_FLASH, (PIN_FLASH_HOLD | PIN_FLASH_WP));
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
|
|
/* Set GPIO pins as outputs. */
|
|
GPIO1_DIR |= (PIN_FLASH_HOLD | PIN_FLASH_WP);
|
|
GPIO5_DIR |= PIN_SSP0_SSEL;
|
|
|
|
/* initialize SSP0 */
|
|
ssp_init(SSP0_NUM,
|
|
SSP_DATA_8BITS,
|
|
SSP_FRAME_SPI,
|
|
SSP_CPOL_0_CPHA_0,
|
|
serial_clock_rate,
|
|
clock_prescale_rate,
|
|
SSP_MODE_NORMAL,
|
|
SSP_MASTER,
|
|
SSP_SLAVE_OUT_ENABLE);
|
|
|
|
device_id = 0;
|
|
|
|
while(1)
|
|
{
|
|
if(device_id == W25Q80BV_DEVICE_ID_RES)
|
|
break;
|
|
|
|
if(device_id == S25FL032P_DEVICE_ID_RES)
|
|
break;
|
|
|
|
device_id = w25q80bv_get_device_id();
|
|
}
|
|
}
|
|
|
|
uint8_t w25q80bv_get_status(void)
|
|
{
|
|
uint8_t value;
|
|
|
|
gpio_clear(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
ssp_transfer(SSP0_NUM, W25Q80BV_READ_STATUS1);
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
|
|
return value;
|
|
}
|
|
|
|
/* Release power down / Device ID */
|
|
uint8_t w25q80bv_get_device_id(void)
|
|
{
|
|
uint8_t value;
|
|
|
|
gpio_clear(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
ssp_transfer(SSP0_NUM, W25Q80BV_DEVICE_ID);
|
|
|
|
/* Read 3 dummy bytes */
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
/* Read Device ID shall return 0x13 for W25Q80BV */
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
|
|
return value;
|
|
}
|
|
|
|
void w25q80bv_get_unique_id(w25q80bv_unique_id_t* unique_id)
|
|
{
|
|
int i;
|
|
uint8_t value;
|
|
uint32_t addr;
|
|
|
|
gpio_clear(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
|
|
if(device_id == W25Q80BV_DEVICE_ID_RES)
|
|
{
|
|
ssp_transfer(SSP0_NUM, W25Q80BV_UNIQUE_ID);
|
|
|
|
/* Read 4 dummy bytes */
|
|
for(i=0; i<4; i++)
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
|
|
/* Read Unique ID 64bits (8*8) */
|
|
for(i=0; i<8; i++)
|
|
{
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
unique_id->id_8b[i] = value;
|
|
}
|
|
}else if(device_id == S25FL032P_DEVICE_ID_RES)
|
|
{
|
|
addr = S25FL032P_OTP_SN1_ADDR;
|
|
ssp_transfer(SSP0_NUM, S25FL032P_READ_OTP);
|
|
ssp_transfer(SSP0_NUM, (addr & 0xFF0000) >> 16);
|
|
ssp_transfer(SSP0_NUM, (addr & 0xFF00) >> 8);
|
|
ssp_transfer(SSP0_NUM, addr & 0xFF);
|
|
ssp_transfer(SSP0_NUM, 0xFF); /* Dummy byte */
|
|
|
|
/* Read Unique ID 64bits (8*8) */
|
|
for(i=0; i<8; i++)
|
|
{
|
|
value = ssp_transfer(SSP0_NUM, 0xFF);
|
|
unique_id->id_8b[i] = value;
|
|
}
|
|
}
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
}
|
|
|
|
void w25q80bv_wait_while_busy(void)
|
|
{
|
|
while (w25q80bv_get_status() & W25Q80BV_STATUS_BUSY);
|
|
}
|
|
|
|
void w25q80bv_write_enable(void)
|
|
{
|
|
w25q80bv_wait_while_busy();
|
|
gpio_clear(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
ssp_transfer(SSP0_NUM, W25Q80BV_WRITE_ENABLE);
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
}
|
|
|
|
void w25q80bv_chip_erase(void)
|
|
{
|
|
device_id = 0;
|
|
while(1)
|
|
{
|
|
if(device_id == W25Q80BV_DEVICE_ID_RES)
|
|
break;
|
|
|
|
if(device_id == S25FL032P_DEVICE_ID_RES)
|
|
break;
|
|
|
|
device_id = w25q80bv_get_device_id();
|
|
}
|
|
|
|
w25q80bv_write_enable();
|
|
w25q80bv_wait_while_busy();
|
|
gpio_clear(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
ssp_transfer(SSP0_NUM, W25Q80BV_CHIP_ERASE);
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
}
|
|
|
|
/* 64KB sector erase */
|
|
void w25q80bv_sector_erase(const uint32_t addr)
|
|
{
|
|
device_id = 0;
|
|
while(1)
|
|
{
|
|
if(device_id == W25Q80BV_DEVICE_ID_RES)
|
|
break;
|
|
|
|
if(device_id == S25FL032P_DEVICE_ID_RES)
|
|
break;
|
|
|
|
device_id = w25q80bv_get_device_id();
|
|
}
|
|
|
|
w25q80bv_write_enable();
|
|
w25q80bv_wait_while_busy();
|
|
gpio_clear(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
ssp_transfer(SSP0_NUM, W25Q80BV_SECTOR_ERASE);
|
|
ssp_transfer(SSP0_NUM, (addr & 0xFF0000) >> 16);
|
|
ssp_transfer(SSP0_NUM, (addr & 0xFF00) >> 8);
|
|
ssp_transfer(SSP0_NUM, addr & 0xFF);
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
}
|
|
|
|
/* write up a 256 byte page or partial page */
|
|
void w25q80bv_page_program(const uint32_t addr, const uint16_t len, const uint8_t* data)
|
|
{
|
|
int i;
|
|
|
|
/* do nothing if asked to write beyond a page boundary */
|
|
if (((addr & 0xFF) + len) > W25Q80BV_PAGE_LEN)
|
|
return;
|
|
|
|
/* do nothing if we would overflow the flash */
|
|
if (addr > (W25Q80BV_NUM_BYTES - len))
|
|
return;
|
|
|
|
w25q80bv_write_enable();
|
|
w25q80bv_wait_while_busy();
|
|
|
|
gpio_clear(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
ssp_transfer(SSP0_NUM, W25Q80BV_PAGE_PROGRAM);
|
|
ssp_transfer(SSP0_NUM, (addr & 0xFF0000) >> 16);
|
|
ssp_transfer(SSP0_NUM, (addr & 0xFF00) >> 8);
|
|
ssp_transfer(SSP0_NUM, addr & 0xFF);
|
|
for (i = 0; i < len; i++)
|
|
ssp_transfer(SSP0_NUM, data[i]);
|
|
|
|
gpio_set(PORT_SSP0_SSEL, PIN_SSP0_SSEL);
|
|
}
|
|
|
|
/* write an arbitrary number of bytes */
|
|
void w25q80bv_program(uint32_t addr, uint32_t len, const uint8_t* data)
|
|
{
|
|
uint16_t first_block_len;
|
|
uint8_t device_id;
|
|
|
|
device_id = 0;
|
|
while(1)
|
|
{
|
|
if(device_id == W25Q80BV_DEVICE_ID_RES)
|
|
break;
|
|
|
|
if(device_id == S25FL032P_DEVICE_ID_RES)
|
|
break;
|
|
|
|
device_id = w25q80bv_get_device_id();
|
|
}
|
|
|
|
/* do nothing if we would overflow the flash */
|
|
if ((len > W25Q80BV_NUM_BYTES) || (addr > W25Q80BV_NUM_BYTES)
|
|
|| ((addr + len) > W25Q80BV_NUM_BYTES))
|
|
return;
|
|
|
|
/* handle start not at page boundary */
|
|
first_block_len = W25Q80BV_PAGE_LEN - (addr % W25Q80BV_PAGE_LEN);
|
|
if (len < first_block_len)
|
|
first_block_len = len;
|
|
if (first_block_len) {
|
|
w25q80bv_page_program(addr, first_block_len, data);
|
|
addr += first_block_len;
|
|
data += first_block_len;
|
|
len -= first_block_len;
|
|
}
|
|
|
|
/* one page at a time on boundaries */
|
|
while (len >= W25Q80BV_PAGE_LEN) {
|
|
w25q80bv_page_program(addr, W25Q80BV_PAGE_LEN, data);
|
|
addr += W25Q80BV_PAGE_LEN;
|
|
data += W25Q80BV_PAGE_LEN;
|
|
len -= W25Q80BV_PAGE_LEN;
|
|
}
|
|
|
|
/* handle end not at page boundary */
|
|
if (len) {
|
|
w25q80bv_page_program(addr, len, data);
|
|
}
|
|
}
|