You've already forked Easyduino
mirror of
https://github.com/Hanqaqa/Easyduino.git
synced 2026-09-01 19:21:51 +00:00
95 lines
3.5 KiB
Markdown
95 lines
3.5 KiB
Markdown
# Easyduino Arduino Nano
|
|
|
|
The popular Nano version of the Arduino
|
|
|
|
<p align="center">
|
|
<img src="https://github.com/Hanqaqa/Easyduino/blob/master/Atmega328p%20Arduino%20Nano/ProductionFiles/Photos/Easyduino%20Nano%20Iso.jpg" width="60%">
|
|
</p>
|
|
|
|
## Schematic
|
|
|
|
<p align="center">
|
|
<img src="https://github.com/Hanqaqa/Easyduino/blob/master/Atmega328p%20Arduino%20Nano/ProductionFiles/PDFs/Schematic_Page_1.png" width="60%">
|
|
</p>
|
|
|
|
## Gerbers
|
|
|
|
<p align="center">
|
|
<img src="https://github.com/Hanqaqa/Easyduino/blob/master/Atmega328p%20Arduino%20Nano/ProductionFiles/PDFs/Gerbers.png" width="60%">
|
|
</p>
|
|
|
|
## Specs
|
|
|
|
- Input Voltage: 5.5V-9V(External Source Vin) 5V (USB). Both can be used at the same time. Preferable to only power from one source
|
|
- Output Current: 250 mA (External Source) 500mA (USB)
|
|
- 3.3V Output Current: None (External Source) 100 mA (USB)
|
|
- No Polarity Protection (External Source)
|
|
- Overcurrent Protection: None (External Source) 1A (USB)
|
|
- 5V Autoselector: can take both USB and external source. A diode will avoid short circuit.
|
|
- External input Polarity Protection: None!!
|
|
|
|
## References
|
|
|
|
### Atmega 328p
|
|
|
|
#### Reset
|
|
|
|
- Atmega Hardware Design Considerations p7,p8 -> 10kR and 330R for switch. The 100nF capacitor is not used for Arduino (Produces errors with DTR)
|
|
- The 100nF capacitor on DTR (CP2102) is used for tricking the Atmega into Bootloader mode
|
|
|
|
#### Crystal
|
|
|
|
- Atmega Hardware Design Considerations p16 -> 22pf
|
|
|
|
#### AVCC
|
|
|
|
- Atmega328 Reference Manual p213 -> 10uH ferrite bead and 100nF.
|
|
- The Analog tracks aren't critical. I won't create an analog ground for these tracks.
|
|
- I also won't add the 10 uH ferrite
|
|
|
|
#### AREF
|
|
|
|
- Atmega Hardware Design Considerations p6 -> 100nF
|
|
|
|
### USB-C
|
|
|
|
#### Filtering
|
|
|
|
- USB Hardware Design Guidelines for FTDI ICs p8 -> 10nF Cap + Ferrite Bead + 100nF Cap + 4.7uF Cap
|
|
- I disregarded such heavy filtering for the easier to implement 1uF and 100nF cap given in the CP2102 datasheet
|
|
- I added a polyfuse with Ihold=500mA and Itrip=1A.
|
|
|
|
#### Differential Pair
|
|
|
|
- USB needs 90 Ohm differential traces.
|
|
- According to JLCPCB impedance calculator, with a JLC7628 prepreg and 6mil (0.15mm) space between lines
|
|
|
|
- I have to use 9 mil tracks -> 0.2 mm
|
|
- I will use a very short trace for D+ D- (around 2mm)
|
|
- I have to place vias because of the pinout of USB C and CP2102. Some other people have done it with no problems
|
|
|
|
#### CP2102
|
|
|
|
- CP2102 datasheet p15 -> 1uF and 100nF for REGIN and VBUS
|
|
- CP2102 datasheet p15 -> 100nF for VDD output, 4.7 uF is optional for higher current circuits.
|
|
- CP2102 datasheet p23 -> The VDD or 3.3 output can only provide 100mA
|
|
- CP2102 datasheet p23 -> Logic levels go up to 3.3 V, but Atmega328p is able to understand them. Despite being 5V
|
|
- CP2102 datasheet p15 -> RST and SUSPEND resistors have not been placed. Might produce bad results due to noise
|
|
|
|
#### XC6206P
|
|
|
|
- XC6206 Torex Datasheet p1 -> 1uF ceramic capacitor on input and output. 7V Maximum operating Voltage
|
|
- XC6206 UWM Datasheet p2 -> 1uF ceramic capacitor on the input and output. 9V Maximum operating Voltage
|
|
|
|
#### 5V autoselector
|
|
|
|
- If USB is present and no external input voltage. The USB will power the ATMEGA
|
|
- If USB is present and there is external input voltage. The external voltage will power the ATMEGA
|
|
- If USB is not present and there is external input voltage. The external voltage will power the ATMEGA. The 3.3V output won't work
|
|
|
|
## KiCad Render
|
|
|
|
<p align="center">
|
|
<img src="https://github.com/Hanqaqa/Easyduino/blob/master/Atmega328p%20Arduino%20Nano/ProductionFiles/Photos/Easyduino%20Nano%20Render%20Iso.jpg" width="60%">
|
|
</p>
|