You've already forked incutec-OpenVTX
mirror of
https://github.com/incutec-hw/OpenVTX.git
synced 2026-08-21 00:10:55 +00:00
a48758a943
Open-source 5.8GHz analog VTX with software-defined OSD based on OpenOSD-X firmware. KiCad 9 project with complete component library (14 symbols, 14 footprints, 13 3D models), all datasheets, reference schematics, and design documentation ready for schematic capture. Co-Authored-By: Claude Opus 4.6 (1M context) <noreply@anthropic.com>
109 lines
3.1 KiB
Markdown
109 lines
3.1 KiB
Markdown
# SKY85743-21 Full Datasheet Extraction
|
|
## Document 204720F, July 29, 2019, Skyworks Solutions
|
|
|
|
## Pinout (24-pin LGA, 3x5mm, top view)
|
|
|
|
| Pin | Name | Description |
|
|
|-----|------|-------------|
|
|
| 1 | GND | Ground |
|
|
| 2 | TX_IN | Transmit Input |
|
|
| 3 | GND | Ground |
|
|
| 4 | PA_EN | PA enable |
|
|
| 5 | GND | Ground |
|
|
| 6 | GND | Ground |
|
|
| 7 | GND | Ground |
|
|
| 8 | DET | Detector output |
|
|
| 9 | GND | Ground |
|
|
| 10 | C1 | Control pin 1 |
|
|
| 11 | GND | Ground |
|
|
| 12 | ANT | Antenna |
|
|
| 13 | C0 | Control pin 0 |
|
|
| 14 | RX_OUT | Switch RX output |
|
|
| 15 | GND | Ground |
|
|
| 16 | LNA_IN | LNA input |
|
|
| 17 | LNA_OUT | LNA output |
|
|
| 18 | GND | Ground |
|
|
| 19 | VDD | LNA supply voltage |
|
|
| 20 | GND | Ground |
|
|
| 21 | GND | Ground |
|
|
| 22 | VCC3 | PA third stage supply |
|
|
| 23 | VCC2 | PA second stage supply |
|
|
| 24 | VCC1 | PA first stage supply |
|
|
| 25 | GND | Exposed pad (thermal) |
|
|
|
|
## Absolute Maximum Ratings
|
|
|
|
| Parameter | Max |
|
|
|-----------|-----|
|
|
| VCC (all supplies) | 6.0V |
|
|
| Control pin voltage | 3.6V |
|
|
| **Input power TX_IN** | **+10 dBm** |
|
|
| Supply current | 800mA |
|
|
| Junction temp | 160°C |
|
|
| Theta_JC | 34°C/W |
|
|
|
|
## TX Mode Specs (VCC=5V, 25°C)
|
|
|
|
| Parameter | Min | Typ | Max |
|
|
|-----------|-----|-----|-----|
|
|
| Frequency | 5.15 | — | 5.925 GHz |
|
|
| Gain (small signal) | 32 | 34 | — dB |
|
|
| MCS0 HT20 Pout | 25 | **27** | — dBm |
|
|
| MCS7 Pout | 23 | 25 | — dBm |
|
|
| MCS9 Pout | 22 | 24 | — dBm |
|
|
| MCS11 Pout (-43dB DEVM) | 18 | 21 | — dBm |
|
|
| Current @ quiescent | — | 190 | 200 mA |
|
|
| Current @ +21dBm | — | 270 | 300 mA |
|
|
| Current @ +25dBm | — | 360 | 400 mA |
|
|
| Current @ +27dBm | — | 410 | 455 mA |
|
|
| 2nd harmonic @ +27dBm | — | -50 | -43 dBm/MHz |
|
|
| Input return loss | — | — | 9 dB |
|
|
|
|
**CW Psat estimate: +27 dBm typ (500mW), possibly +28-29 dBm (630-800mW)**
|
|
Based on MCS0 HT20 rating of +27dBm typ.
|
|
|
|
## Power Detector
|
|
|
|
| Parameter | Min | Typ | Max |
|
|
|-----------|-----|-----|-----|
|
|
| VDET @ +5dBm | 0.26 | 0.33 | 0.39 V |
|
|
| VDET @ +10dBm | 0.40 | 0.46 | 0.53 V |
|
|
| VDET @ +21dBm | 0.68 | 0.75 | 0.82 V |
|
|
| VDET @ +28dBm | 0.85 | 0.93 | 1.00 V |
|
|
| Slope | — | 21-26 | — mV/dB |
|
|
| Error (+10 to +28dBm) | — | — | 1.5 dB pk-pk |
|
|
| Output impedance | — | 100 | 220 ohm |
|
|
|
|
Logarithmic, temperature-compensated. 23dB dynamic range (+5 to +28 dBm).
|
|
|
|
## Control Truth Table
|
|
|
|
| Mode | PA_EN | C0 | C1 |
|
|
|------|-------|----|----|
|
|
| **TX to ANT** | **1** | **0** | **1** |
|
|
| RX LNA | 0 | 1 | 0 |
|
|
| RX bypass | 0 | 1 | 1 |
|
|
| All off | 0 | 0 | 0 |
|
|
|
|
For TX-only: tie PA_EN=VCC, C1=VCC, C0=GND.
|
|
|
|
## Decoupling (from eval board BOM)
|
|
|
|
| Pin | Cap | Value |
|
|
|-----|-----|-------|
|
|
| VCC1 (24) | C6+C9 | 2x 100nF |
|
|
| VCC2 (23) | C1 | 10µF |
|
|
| VCC3 (22) | C3 | 100nF |
|
|
| VDD (19) | C2 | 1nF |
|
|
| TX_IN (2) | C7 | 10pF DC block |
|
|
| DET (8) | C5 | 10pF |
|
|
| LNA_OUT (17) | C8 | 10pF DC block |
|
|
|
|
## Critical Design Notes
|
|
|
|
- TX_IN is DC-shorted to GND internally — use 10pF DC blocking cap
|
|
- ANT is DC-blocked internally — no external cap needed
|
|
- Max input power +10dBm — RTC6705 outputs +13dBm, MUST attenuate
|
|
- Supply: 5V (4.2-5.5V range) — needs separate 5V rail, NOT 3.3V
|
|
- Thermal pad must have via array (0.3mm drill, 0.6mm pitch, resin-filled)
|