mirror of
https://github.com/uw-midsun/hardware.git
synced 2024-11-27 00:00:38 +00:00
0f58f98c8a
* ELEC-304 Lights Board Rev 1.0 - First revision of schematic Schematic Library: - Added MOSFET P-CH 20V 5A 6-TSOP - Modified MOSFET N-CH 30V 8.7A 2.1W 6-PQDN(2x2). Put all the drains one wire. Footprint Library: - Added MOSFET P-CH 20V 5A 6-TSOP * Elec 304 - Revision #2 for lights board. Changed to high side driver for the headlights and using n mosfet now instead of p mosfet and n mosfet for the rest of the lights. * elec 304- revision 1.1 Changed to high side drivers for headlights. For the other lights changed to n mosfe. * elec 304 Revision 1.2 Schematic Library: Added 1K resistor array PCB footprint: Added 1K resistor array (note: pcb looks strange/is it ok) - Fixed high side driver schematic symbol (note: can't * elec 304 - Revision 1.2 Schematic library: added 1K resistor array PCB footprint: added 1K resistor array (Note: footprint for resistor array looks strange/is it correct?) - Fixed schematic for high side driver - Fixed LEDs (not sure how to add jumpers to disable LEDs) - Changed everything so GND on bottom and 12V on top - Made names more descriptive * elec 304 - Revision 1.3 Made changes: - so connector pin 1 is on top - added jumpers to LED - HSD and resistor array should be updated on schematic library - changed harness names to more descriptive * elec 304 - Revision 1.4 - leds are now connected to one jumper wire - components are on grid * elec 304 - Revision 1.0 for PCB - started PCB design * elec 304- Revision 1.1 of PCB Design - new layout - larger board size * elec 304 revision 1.5 Changes made: - made schematic neater (font size/alignment) - fixed dual package - fixed pcb footprints - added 12v connector - added GPIO input to determine front or back - changed from HSD to load switch - added schematic and footprint for load switch being used - capacitor still has to be addded to output of load switch - NO CHANGES to PCB * elec 304 - Revision 1.6 - Added capacitors after load switch - remoived resistor array; load switch has internal one - made schematic more organized * elec 304 - revision 1.7 * elec 304 - revision 1.8 * elec 304 - revision 1.9 - finished first draft of PCB design - 4 layour board - load switches switched to active high - added capacitors to schematics - no changes made to library/footprint - seperated headlight sheets into two seperate sheets * elec 304 - revision 1.10 - added 200 ohm resistor between VOUT and Bleed - added 200 ohm resistor to schematic and PCB library - added polygon pours for all connectors/ used thicker traces - added more silkscreen - fixed schematic (added titles/resistors) - having trouble connecting pin 7 and 8, the copper bridge between the two of them is causing trouble? except for the 4 HSD for high/low beam * Library Update - Updated IC LOAD SWITCH... with 3D model and pin 1 dot - Updated MOSFET 2NFET... with 3D model - Updated CAP 56uF... with cylinder extrude - Updated IC LOAD SWITCH... to not have polygon but have another pad instead * elec 304 - revision 1.11 - changed connector pins to make it more organized - changed GND polygon pours to traces - added silkscreen for LED - made the board 1cm smaller on the right side - fixed traces (straight traces) - fixed HSD error by fixing the pcb footprint - instead of putting the two connectors (P5 and P3) together because that would fix the left and right side together i could use a 4 pin connector?? * elec 304 - revision 1.12 -fixed 90 degrees traces -fixed traces and polygon pours to make it more organized - added diode to the horn/strobe * elec 304 - revision 1.13 - combined rear brake/turn lights with the connectors being used for headlights at the front - replaced horn/strobe with HSD - made board smaller so now 70mm by 70mm - added GPIO pin for determining front/back of the board - changed wiring around/added GPIO pins so wiring could be less cluttered around the controller board region * elec 304 - revision 1.14 - made silkscreen neater - fixed bad connection from previous version - moved components further away from connector - added bulk capacitor to horn/strobe - to do: fix JP2 * elec 304 - revision 1.15 - added more silkscreen to the back - made silkscreen clearer at front - made schematic more clear * elec 304 - reivision 1.16 - fixed JP2 * elec 304 - revision 1.17 - fixed unrouted nets * elec 304 - revision 1.18 - made traces by controller board neater/less 45 degree angle traces * elec 304 - revision 1.19 - changed connectors so all is white except for power -added schottky diode to PCB library, schematic library * - Minor change to layout and silkscreen - Generated output files. * elec 304 - started block diagram * elec 304 - added MOSFET N-CH 30V 8.7A 2.1W 6-PQFN (2x2) - added IC LOAD SWITCH ACT-HI - added DIODE SCHOTTKY 60V 7A POWERDIS - added CAP ALUM 56 UF 20% 35V Radial - added RES SMD 200 OHM * Merging library, renumbered sheets
2 lines
109 B
Plaintext
2 lines
109 B
Plaintext
MSXII_Headlights_Left=PA8/LOW_BEAM/LR_OUTER_BRAKE,PB15/HI_BEAM/RE_BRAKE,PA10/L_DRL/LR_OUTER_TURN,PA9//L_TURN
|